Does a rear blade fit a TYM T254?
On paper, the TYM T254 clears 0 of 8 curated rear blade classes in our catalog, with 3 Partial (at least one limit not confirmed) and 5 incompatible. Most common fail check: sub-compact suitability (5 of 8 classes). Checks use verified hitch/PTO overlays, lift Facts and maker-published HP limits. We never invent a number.
- compatible
- 0 compatible
- partial
- 3 partial
- incompatible
- 5 incompatible
Open in Fit checker →Implement hub →Fit guide →Tractor profile →
Verified Facts for this tractor
- Engine HP
- 23.9 HP
- Hitch
- Limited Category I
- PTO HP
- 18.8 PTO HP
- PTO RPM
- 540
- Rear lift
- 1,101 lbs
Before you buy
- TYM T254 is sub-compact. Lower rear lift often fails five-foot and heavier rear blade classes even when engine HP looks close, and its Limited Category I hitch shows Partial on implements listed only for full Category I.
- Verified hitch: Limited Category I. Implements that name Limited Category I pass the hitch check. Implements listed only for full Category I show Partial: check the lower-link pin spacing and tower height in the tractor's operator's manual. Adapters do not add lift.
- Verified PTO rating: 18.8 PTO HP. Size PTO implements from this number — not from engine HP.
- Catalog rear lift: 1,101 lbs. Measurement point not on file. Heavier rear blade tools need headroom over shipping weight (we screen with ~20% margin).
- No class is a confirmed fit yet: 3 Partial. Each Partial row names the number we couldn't confirm. Check it on the maker's sheet, then re-check.
- Next step: open the Fit checker with TYM T254 and a specific rear blade model, or read the fit guide for this implement type.
What Fit checks for this implement type
Rear blades are typically non-PTO scraping tools. Hitch category and rear lift drive paper Fit; angle and offset kits do not raise tractor ratings.
What usually fails first
Lift capacity and hitch class on light frames. Heavier utility blades want more mass than a sub-compact can safely carry.
How to use this hub
Compare hitch and weight Facts below, then run Fit.
On the TYM T254
On the TYM T254, no curated class is a confirmed fit yet: 3 Partial, most often on the hitch category. For 7 rows, the tractor has a Limited Category I hitch. Partial is never a confirmed fit.
Results by implement class
Land Pride RB1660 Rear Blade
Needs a closer look- Hitch size: Limited Category I hitch: Cat I pins fit, but check the implement's lower-link pin spacing and tower height against the tractor's operator's manual.
- PTO power: Implement does not require PTO horsepower.
- Upper HP limit: Tractor engine HP (23.9) and PTO HP (18.8) are both within the maker's 40 HP maximum for this blade.
- PTO speed: Implement does not require a PTO RPM match.
- Rear lift capacity: 1101 lb lift clears ~340 lb required (weight + 20%).
- Sub-compact size: Implement is marked suitable for sub-compact geometry.
Land Pride RB1672 Rear Blade
Needs a closer look- Hitch size: Limited Category I hitch: Cat I pins fit, but check the implement's lower-link pin spacing and tower height against the tractor's operator's manual.
- PTO power: Implement does not require PTO horsepower.
- Upper HP limit: Tractor engine HP (23.9) and PTO HP (18.8) are both within the maker's 40 HP maximum for this blade.
- PTO speed: Implement does not require a PTO RPM match.
- Rear lift capacity: 1101 lb lift clears ~357 lb required (weight + 20%).
- Sub-compact size: Implement is marked suitable for sub-compact geometry.
60″ rear blade (compact class)
Needs a closer look- Hitch size: Limited Category I matches implement hitch options.
- PTO power: Implement does not require PTO horsepower.
- Upper HP limit: Upper HP limit not on file yet — check the maker's sheet.
- PTO speed: Implement does not require a PTO RPM match.
- Rear lift capacity: 1101 lb lift clears ~420 lb required (weight + 20%).
- Sub-compact size: Implement is marked suitable for sub-compact geometry.
Land Pride RB1684 Rear Blade
Not a fit on paper- Hitch size: Limited Category I hitch: Cat I pins fit, but check the implement's lower-link pin spacing and tower height against the tractor's operator's manual.
- PTO power: Implement does not require PTO horsepower.
- Upper HP limit: Tractor engine HP (23.9) and PTO HP (18.8) are both within the maker's 40 HP maximum for this blade.
- PTO speed: Implement does not require a PTO RPM match.
- Rear lift capacity: 1101 lb lift clears ~383 lb required (weight + 20%).
- Sub-compact size: Implement is not marked suitable for sub-compact hitch geometry / frame size.
Land Pride RB2672 Rear Blade
Not a fit on paper- Hitch size: Limited Category I hitch: Cat I pins fit, but check the implement's lower-link pin spacing and tower height against the tractor's operator's manual.
- PTO power: Implement does not require PTO horsepower.
- Upper HP limit: Tractor engine HP (23.9) and PTO HP (18.8) are both within the maker's 60 HP maximum for this blade.
- PTO speed: Implement does not require a PTO RPM match.
- Rear lift capacity: 1101 lb lift clears ~443 lb required (weight + 20%).
- Sub-compact size: Implement is not marked suitable for sub-compact hitch geometry / frame size.
Land Pride RB2684 Rear Blade
Not a fit on paper- Hitch size: Limited Category I hitch: Cat I pins fit, but check the implement's lower-link pin spacing and tower height against the tractor's operator's manual.
- PTO power: Implement does not require PTO horsepower.
- Upper HP limit: Tractor engine HP (23.9) and PTO HP (18.8) are both within the maker's 60 HP maximum for this blade.
- PTO speed: Implement does not require a PTO RPM match.
- Rear lift capacity: 1101 lb lift clears ~476 lb required (weight + 20%).
- Sub-compact size: Implement is not marked suitable for sub-compact hitch geometry / frame size.
Land Pride RB2696 Rear Blade
Not a fit on paper- Hitch size: Limited Category I hitch: Cat I pins fit, but check the implement's lower-link pin spacing and tower height against the tractor's operator's manual.
- PTO power: Implement does not require PTO horsepower.
- Upper HP limit: Tractor engine HP (23.9) and PTO HP (18.8) are both within the maker's 60 HP maximum for this blade.
- PTO speed: Implement does not require a PTO RPM match.
- Rear lift capacity: 1101 lb lift clears ~510 lb required (weight + 20%).
- Sub-compact size: Implement is not marked suitable for sub-compact hitch geometry / frame size.
72″ rear blade (compact class)
Not a fit on paper- Hitch size: Limited Category I hitch: Cat I pins fit, but check the implement's lower-link pin spacing and tower height against the tractor's operator's manual.
- PTO power: Implement does not require PTO horsepower.
- Upper HP limit: Upper HP limit not on file yet — check the maker's sheet.
- PTO speed: Implement does not require a PTO RPM match.
- Rear lift capacity: 1101 lb lift clears ~504 lb required (weight + 20%).
- Sub-compact size: Implement is not marked suitable for sub-compact hitch geometry / frame size.
Attachment numbers come from the manufacturer specification sheet linked below. Confirm your serial year before purchase.
Engine HP is not PTO HP. Any number we can't confirm shows as Partial. Verify it on the OEM sheet before purchase.
FAQ
- Which rear blade classes clear on paper for the TYM T254?
- No class is a confirmed fit yet: 3 Partial (Land Pride RB1660 Rear Blade, Land Pride RB1672 Rear Blade, and 60″ rear blade (compact class)). Each Partial row names the number we couldn't confirm. Check it on the maker's sheet, then re-check.
- Why are 3 rear blade rows Partial on the TYM T254?
- Land Pride RB1660 Rear Blade, Land Pride RB1672 Rear Blade, and 60″ rear blade (compact class) are Partial because at least one number can't be confirmed yet, most often the hitch category and upper HP limit. For 7 rows, the tractor has a Limited Category I hitch. The maker's upper HP limit for 2 of these rows isn't on file yet. Partial is never a confirmed fit.
- What does Partial mean?
- Partial means one number can't be confirmed yet: a tractor Fact the check needs (PTO HP, PTO speed, hitch or rear lift) isn't on file, or the maker's upper HP limit isn't on file or isn't published. Partial also shows when only engine HP is known and it's over the maker's HP limit; when the tractor has two published PTO figures and only one is within the maker's HP limit (that can depend on the transmission version, so check which one you have); when the maker publishes different HP limits by drivetrain and this tractor is over one of them; or when the maker's own documents give two different limits. Partial is never a confirmed fit. We mark gaps instead of inventing numbers.
- Which rear blade classes fail on the TYM T254?
- 5 class(es) fail — including Land Pride RB1684 Rear Blade, Land Pride RB2672 Rear Blade, and Land Pride RB2684 Rear Blade — usually on sub-compact suitability. Those aren't marked for sub-compact frames.
- How do I check a specific rear blade on the TYM T254?
- Open the Attachment Fit checker with the TYM T254 and rear blade type, open a result row below, or follow the source link on each implement.